Epoxy treatment for transparent coatings

Kodi: SYN.0106

Përbërësit: 2

Pamja: I lëngshëm

Two-component transparent epoxy system, based on epoxy resins in aqueous dispersion, free from solvents, characterised by a high content of solids that provides, after application and curing, a coating with good mechanical resistance and chemical, especially related to contact with oils and solvents.

Linee di appartenenza

Certifikata të fituara dhe Rregullore

Produkte dhe sisteme për mbrojtjen e riparimin e strukturave prej betoni – Sisteme mbrojtjeje për sipërfaqe betoni

EN 1504-2

Produkte dhe sisteme për mbrojtjen e riparimin e strukturave prej betoni – Sisteme mbrojtjeje për sipërfaqe betoni

Vetitë themelore


I pandezshëm


Jetëgjatësia: 12 muaj


Pa tretës


Pesha specifike: 1.09 kg/l


Pot life: 80 -120 min


Raporti i përzierjes: 1:1 _


Të përdoret me doreza mbrojtëse


Temperatura e aplikimit: +5 / +35 °C

Veçoritë teknike

Ngurtësim në prekje

0.5 h

Ngurtësimi i plotë

7 ditë

Përthitha kapilare



Comp A 14700 / Comp B 20500 mPa


24 h

Ngjyrat në dispozicion

- E tejdukshme

Amballazhime dhe përmasa

- Kanoçe 10 kg [B]

- Kanoçe 10 kg [A]

- Kanoçe 5 kg [A]

- Kanoçe 5 kg [B]

- Kavanoz 1 kg [A]

- Kavanoz 1 kg [B]

- Kit: 1 Kavanoz 1 kg [A] + 1 Kavanoz 1 kg [B]

- Kit: 1 Kanoçe 5 kg [A] + 1 Kanoçe 5 kg [B]

- Kit: 1 Kanoçe 10 kg [A] + 1 Kanoçe 10 kg [B]


From 0.10 to 0.15 kg of SYNTYECH PAVISHEER for each square metre of surface to be covered.

Fushat e përdorimit

Transparent finish of interior floor coverings, mechanical-resistant impregnations, anti-dust and anti-oil for concrete surfaces.

Përgatitja e shtresave

The media should have adequate mechanical resistance. The concrete surfaces should be cured, dry, planar and absorbent, free from oils, detergents, powders and soiling. The most appropriate type of mechanical preparation should also be determined (degreasing or shot peening).

Conveniently absorbent surfaces may be dealt with directly after a proper cleaning. For tiled surfaces and for pre-existing coverings in resin, a degreasing or shot peening treatment is required until complete opacification and complete elimination of dust.

Mënyra e përdorimit

Mix components A and B each in their own container before mixing. Do not take partial quantities from the packs to avoid any errors in the mixing ratio that would cause failure or incomplete hardening. Pour component B into a suitable container and add component A. Mix everything for a few minutes using a mechanical stirrer with variable speed until a homogeneous and uniform color mixture is obtained. Leave to rest for a few minutes and mix again. Dilute the final product only with water in the SYNTECH PAVISHEER: water ratio of 1: 3 for the first coat and 1: 2 for the second. Gradually add the dilution water, continuing to mix for a few minutes. The dilution ratio can vary according to the porosity of the support; if necessary on closed surfaces it is also possible to dilute the second coat respecting the dilution ratio 1: 3. The SYNTECH PAVISHEER emulsion has a stability of about 2 hours at 20 ° C; within this period the product must be used. SYNTECH PAVISHEER is applied with a short-haired roller or spray, covering the entire surface evenly. We recommend application at temperatures not lower than 5 ° C.

Mënyrat e përdorimit

- Brushë

- Rrul

Mjetet e pastrimit

- Ujë

Shtresat e lejuara

- Beton

- Parafabrikuara

- Tulla dhe pllaka

- Nënshtresa çimentoje

- Faqe shkëmbore

Na kontaktoni

Vuoi saperne di più sui nostri prodotti?

Kujdes, plotëso saktë këtë fushë.
Kujdes, fut një adresë email-i të vlefshëm.
Kujdes, plotëso saktë këtë fushë.

Duke paraqitur pranoj politikat e privatësisë

Kujdes, plotëso saktë këtë fushë.

Përfundimi regjistrim në Newletter


Produkte në vitrinë

  • Concrete Repar
  • Readymesh
  • Grout Power