SANAWARME

Insulating plaster, dehumidifying, high thermo-acoustic performance

Kodi: INT.0169

Përbërësit: 1

Pamja: Pluhur

A thermal, external-coating macroporous plaster with high thermal and acoustic insulation, it has a base of natural hydraulic lime NHL 3.5, natural hydraulic binders with low soluble salt content and low environmental impact, botticino marble, kaolin, calcium casein, Vichy salt, calcium carbonate, tartaric acid, ammonium salts, expanded perlite, cork powder, natural fibres along wth specific and antisaline agents for the dehumidification, thermal and hygrometric restoration of buildings and masonry, in green building works, for new constructions and in the restoration of historic and monumental buildings. Specifically for applying “mineral coatings”. A mortar/plaster with guaranteed performance offering specific insulating properties pursuant to UNI EN 998/1 – Class T1 (the top thermal insulation class). Thermal conductivity certified pursuant to UNI EN 12664.

Linee di appartenenza

Certifikata të fituara dhe Rregullore

Specification for Mortar for Masonry - Mortars for thermal insulation (T1)

EN 998-1

Specification for Mortar for Masonry - Mortars for thermal insulation (T1)

Pretendimet mjedisore të përmbajtjes së materialit të ricikluar

EN 14021:2016

Pretendimet mjedisore të përmbajtjes së materialit të ricikluar

A + (emisione shumë të ulta)

EMISSIONS DANS L'AIR INTERIEUR

A + (emisione shumë të ulta)

Vetitë themelore

aplikojeni-me-dy-duar

Aplikojeni me dy duar

i-pandezshëm

I pandezshëm

jetëgjatësia

Jetëgjatësia: 12 muaj

material-100-eco-friendly

Material 100% eco-friendly

përmasa-maksimale-e-agregatit

Përmasa maksimale e agregatit: 2.5 mm

përzierja-me-ujë

Përzierja me ujë: 55 - 62 %

pot-life

Pot life: 60 - 75 min

produkt-në-dukje

Produkt në dukje

rezistent-ndaj-rrezeve-uv

Rezistent ndaj rrezeve UV

temperatura-e-aplikimit

Temperatura e aplikimit: +8 / +30 °C

trashësia-maksimale-e-lejueshme

Trashësia maksimale e lejueshme: 10 cm

trashësia-minimale-e-lejueshme

Trashësia minimale e lejueshme: 3 cm

Veçoritë teknike

Lidhja e aderimit

0.18 N/mm²

Masa vëllimore

~ 400 kg/m³

Moduli elastik

< 3000 N/mm²

Nxehtësia specifike

1 kJ/kgK

Përmbajtja totale e ricikluar

4.9 %

Përthitha kapilare

0.35 kg•h^0.5/m²

Reagimi ndaj zjarrit

A1 _

Rezistenca në përkulje pas 28 ditësh

> 1 N/mm²

Rezistenca nga ngjeshja

> 3 N/mm²

Thermal conductivity

0.077 W/m*K

Traspirimi

9 μ

Ngjyrat në dispozicion

- Gështenjë e hapur

Amballazhime dhe përmasa

- Qese 13 kg

- Koli: 50 x (Qese 13 kg)

Vetitë

SANAWARME is the highest technological expression of Azichem in the context of renovating plasters. It is a product based on hydraulic lime, botticino, kaolin, calcium caseinate, Vichy salt, calcium carbonate, tartaric acid, ammonium salts, expanded perlite, cork powder and natural fibres. SANAWARME is characterised by high hygroscopic, breathable and thermal/acoustic insulation properties. It is a "thermal mineral coating", natural, for ecological building, that does not contain cements, resins, solvents and radioemissive materials.

The structure of the coatings made with SANAWARME, which is particularly suited to quieten and dissipate, in the form of heat, the acoustic energy inside the pores and "channels", provides interesting performance even in terms of sound absorption which, at high frequencies, reaches values of 1/3, with interesting prospects for acoustic correction of the internal environment (Test Report no. 214705 of August 3, 2006 issued by the institute Giordano).

Konsumi

Approximately 4,00 - 4,50 kg/m² of SANAWARME for every centimetre of thickness to be implemented (approximately 420 kg per cubic metre).

Fushat e përdorimit

Applying coating plasters in both new constructions, and in interventions of restoration and renovation of old buildings. Anti-condensation and mildewcide correction for indoor, out of the ground and buried surfaces. Insulation of thermal bridges.

Përgatitja e shtresave

Removal of crumbling plaster, if present. The wall bodies for application should in any case be clean, intact, free from fouling, dust, crumbling and non-adhering parts, conveniently saturated with water until it reaches the condition of "saturated dry surface".

In the presence of salt efflorescence it will be necessary to ensure its careful removal by application of packs of the specific acid detergent and saline converter DETERG-A, in solution with water 1:4. To prevent any new spills of salts, use specific universal anti-saline treatments in aqueous solution, SANAREG, for humid surfaces, or solvent-based, FEST SALZ, for cohesive saline concretions but with perfectly dry surfaces.

Mënyra e përdorimit

Preliminary construction of specific anchoring scratch coats, breathable, made with UNTERSANA. The rendering, applied by "spraying", must provide a rough, corrugated surface, designed to promote the bonding of the subsequent plaster, which must be applied no later than 2-3 days. In the case of wooden surfaces, attach a galvanized steel wire mesh, diameter 2 mm and mesh 5x5 cm, to the support, holding it away from the surface by 2-3 mm. Spray the rendering UNTERSANA by hand or by plastering machine, in order to provide a rough surface, designed to facilitate the application and the adhesion of SANAWARME. In the case of applying the thermal coat SANAWARME on concrete, it is recommended to apply the super-adhesive rendering REPAR PLUG.

Prepare the plaster, adding SANAWARME, to the mixing water, for approximately 60-70% by weight (8.5 -9 litres per 13 kg bag). Mix thoroughly until it reaches a smooth, creamy, lightweight, lump-free mixture resembling a "compact foam". Apply the thickness required according to the thermal calculation by plastering machine (type PFT model G4, or the like, equipped with lung for light plasters). For small sizes it is also possible to apply it manually with straight edge and plastic mortar.

Regularise the plastered surfaces with fine skim SANASTOF for ecological buildings, for an indicative consumption of 4 kg/m². "Drown" in the thickness of the finishing layer the fibreglass mesh ARMAGLASS 160. Successive breathable paints or putty coats (from the series SANAFARBE, SANAXIL or PROTECH SIL) can be applied after approximately 28 days; in any case, after the proper curing of the plaster, depending on the actual environmental conditions, and the loss of initial alkalinity.

Mënyrat e përdorimit

- Mallë

- Makinë suvatimi

- Pompë

- Straight edge

Mjetet e pastrimit

- Ujë

Shtresat e lejuara

- Suva

- Beton

- Llaçe çimentoje, gëlqereje e të përziera

- Parafabrikuara

- Dru

- Fibroçimento

- Tulla

- Muratura të përziera

- Muratura me tulla me vrimë

- Muratura me gurë

Paralajmërime, masa paraprake dhe Ekologji

The fresh surfaces, of the plaster set on-site , should be protected from direct exposure to sunlight, from the rain and the wind and must be cured by prolonged moist hardening.

Over 4cm thick, inclusive of UNTERSANA, SANAWARME and SANASTOF, it is appropriate to insert in the centre thickness of SANAWARME a galvanized steel wire mesh, diameter 2 mm and mesh 5x5 cm, fixed to the masonry by steel connectors with improved adherence, following a square lattice with 1 metre spacing.

Na kontaktoni

Vuoi saperne di più sui nostri prodotti?

Kujdes, plotëso saktë këtë fushë.
Kujdes, fut një adresë email-i të vlefshëm.
Kujdes, plotëso saktë këtë fushë.

Duke paraqitur pranoj politikat e privatësisë

Kujdes, plotëso saktë këtë fushë.

Përfundimi regjistrim në Newletter

Ndaj

Produkte në vitrinë

  • Sanawarme
  • Readymesh
  • Sanageb