SANAFLUENS
Superfluid grout based on reinforcing, injectable hydraulic lime mortar
Kodi: GRT.0154
Përbërësit: 1
Pamja: Pluhur
Powder preparation, ready-to-use, based on hydraulic lime, for the preparation, with the sole addition of water, of grout for masonry reinforcement, injectable and castable, high performance in terms of sliding, strength and stability, for ecological building interventions and the restoration of vintage buildings and monuments.
Familja
Kodi doganor
Linee di appartenenza
Certifikata të fituara dhe Rregullore
EN 998-2
Llaç murature - llaç murature për përdorim të përgjithshëm (G)
M20
EN 998-2
Vetitë themelore
Temperatura e aplikimit: +6 / +30 °C
Dosage: 1.50 - 1.55 kg/dm³
Pot life: 60 min
Jetëgjatësia: 12 muaj
Përzierja me ujë: 22-24 %
Veçoritë teknike
Water penetration after capillary absorption
2.4 mm
Lidhja e aderimit
1.2 N/mm²
Moduli elastik
12000 MPa
Përçueshmëri termike
0.67 W/m*K
Përshkueshmëria e avullit të ujit
15/35 μ
Përthitha kapilare
0.53 kg•h^0.5/m²
Rezistenca nga ngjeshja
> 20 N/mm²
Masa vëllimore
1980 kg/m³
Përmbajtja e klururit
0.0082 %
Rezistenca nga përkulja
> 6 N/mm²
Ngjyrat në dispozicion
- Gri
Amballazhime dhe përmasa
- Koli: 50 x (Qese 25 kg)
- Qese 25 kg
Vetitë
In the SANAFLUENS mixtures, the water is completely and stably incorporated from the hydration reaction of lime; conversely, in traditional mixtures, a very high part of added water, is free, and evapourating, it leaves gaps in the walls.
SANAFLUENS is based on natural hydraulic lime, sodium gluconate, kaolin, aluminates; it does not contain cement, resins, solvents and radioemissive aggregates.
Konsumi
Approximately 1500 kg of SANAFLUENS for each cubic metre of volume to be filled.
Fushat e përdorimit
Wall reinforcements of "bag" masonry or masonry damaged by earthquake by injections.
Përgatitja e shtresave
Clean the application surfaces by spraying abundantly with water. If there is a lack of plaster, apply a suitable render of hydraulic lime and sand (such as UNTERSANA) to close as much as possible the escape routes of the grout once it has been injected. Trace, from bottom to top and from left to right, a 50 cm square grid. On the intersection of the squares, drill the masonry with a rotary drill, with a bit of at least 22 mm in diameter, to a depth of at least 3/5 of its thickness, tilting the drill downwards by about 20 °. Once all the holes have been drilled, they will be sucked up, blown with compressed air and sprayed with water, to remove the dust inside them produced by the drilling. Insert in the holes for a depth of about 5 cm, transparent meshed rubber tubes, with a total length of at least 30 cm (therefore with about 25 cm external). Properly seal the perimeter of the pipe with ANCHORSANA FIX accelerated setting grouting mortar to prevent the injected product from escaping. Inject the grout always keeping it lightly mixed and operating a continuous flow, without interruptions.
Mënyra e përdorimit
Pour about 2/3 of the mixing water into the mixer. Gradually add SANAFLUENS and the water still required, continue to mix until a fluid, homogeneous, lump-free grout of the desired consistency is obtained. The mixing water indicatively necessary is equal to 22-24% by weight (5.5 - 6 litres per bag).
Reinforcing backfills and fills can be carried out both by gravity and using manual or automatic pumps, depending on the type of application. To verify the effectiveness of the reinforcement, the grout will come out of the pipes adjacent to that in which it is injected.
Mënyrat e përdorimit
- Injeksion
- Pompë
- Rrjedhje
Mjetet e pastrimit
- Ujë
Shtresat e lejuara
- Muratura me gurë
- Muratura të përziera
- Tulla
Paralajmërime, masa paraprake dhe Ekologji
An abundant preliminary injection of water into the holes drilled in the masonry is recommended, to allow an adequate and rapid sliding of the grout.
Na kontaktoni
Vuoi saperne di più sui nostri prodotti?
Skeda teknike [ITA]
Skeda teknike [ENG]
Skeda teknike [ESP]
Skeda teknike [POR]
Skeda teknike [DEU]
Skeda teknike [FRA]
Skeda teknike [RUM]
