Kodi: GRT.0071
Përbërësit: 1
Pamja: Pluhur
GROUT 6 SFR is a high-performance, self-levelling castable mortar, being fibre-reinforced with READYMESH MM-150 steel fibres and 6 mm READYMESH PM-060 polypropylene microfibres, with high flexural strength, great adhesion to concrete and steel, and shrinkage compensation. Aggregates with a maximum size of 6 mm. It is ideal for anchoring road joints, restorations, reinforcements and seismic adjustments, offering ductility for medium-to-high thicknesses (5–20 cm), on structures in reinforced concrete and masonry.
EN 1504-3
Produkte dhe sisteme për mbrojtjen dhe riparimin e strukturave në beton – Riparime strukturore dhe jo strukturore (R4)
I pandezshëm
Pot life: 60 min
Përzierja me ujë: 11 - 14 %
Produkt në dukje
Të përdoret me doreza mbrojtëse
Temperatura e aplikimit: +5 / +35 °C
Rezistent ndaj rrezeve UV
Përmasa maksimale e agregatit: 5 mm
Rezistenca në përkulje pas 07 ditësh
> 9 N/mm²
Masa vëllimore
2250 kg/m³
Përmbajtja e klururit
< 0.01 %
Moduli elastik
29 GPa
Rezistenca në përkulje pas 01 ditë
> 5 N/mm²
Rezistenca në ngjeshje pas 01 dite
> 28 N/mm²
Rezistenca në ngjeshje pas 07 ditësh
> 58 N/mm²
Resistenca nga karbonizimi
dk < cls standard mm²/m
Tërhiqni rezistencën në mbështetjen e muraturës, Pull Out
< 0.6 mm
Rezistenca në përkulje pas 28 ditësh
> 12 N/mm²
Rezistenca në ngjeshje pas 28 ditësh
> 75 N/mm²
Lidhja e aderimit
> 2.5 N/mm²
Përthitha kapilare
< 0.40 kg•h^0.5/m²
Thermal compatibility
> 2 N/mm²
- Gri
- Koli: 50 x (Qese 25 kg)
- Qese 25 kg
Approximately 21,50 kg/m² of GROUT 6 SFR for every centimetre of thickness to be implemented (approximately 2150 kg per cubic metre).
Structural restoration and adjustments, recovery and anchoring of road, motorway, airport joints and critical area joints in general.
Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". An adequate roughening of the surfaces by scarifying, sandblasting etc. is always necessary in order to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes).
Pour about 2/3 of the mixing water into the mixer, add GROUT 6 SFR and the remaining water; continue to mix until a homogeneous lump-free mixture is obtained. The mixing water should be about 13%-15% by weight (3.5-4.5 litres per bag). Adopt casting procedures capable of ensuring the absence of discontinuities and avoid the formation of air pockets.
For high anchoring sections it is appropriate to add GHIAIETTO 6.10 (please refer to the appropriate technical data sheet for more information).
- Mallë
- Mistri
- Rrjedhje
- Shpatull
- Ujë
- Asfalt
- Beton
Vuoi saperne di più sui nostri prodotti?