ELASTOCAP-ABC

Specific fixative for the permanent encapsulation of asbestos panels

Kodi: PRT.0388

Përbërësit: 1

Pamja: I lëngshëm

One-component coating based on acrylic resins in aqueous dispersion for permanent encapsulation of type A (visible outside), B (visible inside) and C (not visible, before confinement) of asbestos sheets , certified in accordance with the DM August 20, 1999. ELASTOCAP-ABC is characterized by high flexibility, resistance to yellowing, adhesion and creates a waterproof and crack-resistant membrane.

Kodi doganor
3209 1000

Linee di appartenenza

Certifikata të fituara dhe Rregullore

Veshje kapsuluese për fletët e azbest-çimentos - Ciklet e kapsulimit të tipit A, B, C dhe D

UNI 10686:1998 - D.M. 20/08/1999

Veshje kapsuluese për fletët e azbest-çimentos - Ciklet e kapsulimit të tipit A, B, C dhe D

Vetitë themelore

jetëgjatësia

Jetëgjatësia: 12 muaj

të-përdoret-me-syze-mbrojtëse

Të përdoret me syze mbrojtëse

temperatura-e-aplikimit

Temperatura e aplikimit: +5 / +40 °C

pa-tretës

Pa tretës

rezistent-ndaj-rrezeve-uv

Rezistent ndaj rrezeve UV

aplikojeni-me-dy-duar

Aplikojeni me dy duar

pesha-specifike

Pesha specifike: 1.25 - 1.30 kg/l

dosage

Dosage: 600-650 g/m²

të-përdoret-me-doreza-mbrojtëse

Të përdoret me doreza mbrojtëse

trashësia-minimale-e-lejueshme

Trashësia minimale e lejueshme: 300 μm

Veçoritë teknike

Aderimi pas cikleve të diellit-shiut

1.32 MPa

Rezistenca nga zjarrit

CLASS 1 _

Mbetje e thatë

57 - 60.7 %

Rezistenca ndaj larjes

> 5000 ciklet

Ngjitja në shtresa

1.34 N/mm²

pH

7.5 _

Ngjitja pas cikleve të ngrirjes-shkrirjes

1.3 MPa

Time before second coat

12 - 24 h

Ngurtësimi i plotë

7 ditë

Ngjyrat në dispozicion

- E bardhë

- E kuqe

- Gri

Amballazhime dhe përmasa

- Çisternë 1000 kg

- Kovë 20 kg

Vetitë

ELASTOCAP-ABC is a product certified as being suitable for inertising Type A, Type B and Type C asbestos cement products.

Konsumi

A minimum 0.60 kilograms of ELASTOCAP-ABC per square metre of surface is to be applied in two coats.

Fushat e përdorimit

For visible or invisible permanent encapsulation of flat and corrugated roofing sheets and coverings containing asbestos fibres subject to degradation.

Përgatitja e shtresave

If the surface is intact and only partially affected by the presence of mould and vegetation, it must be adequately suctioned using specific equipment, wet cleaned and treated with biocidal products to prevent dispersing the fibres into the environment and to permit the reclamation of the water used for washing. If the surface is particularly damaged or covered with mould and vegetation, it is necessary to inform the competent Local Health Authority by submitting an appropriate intervention plan. Cleaning in any case must be carried out with low-pressure water that is to be recovered in special containers for the subsequent disposal of the sediments. Any detached parts and waste are to be properly disposed of as asbestos waste. Always operate in compliance with current regulations on asbestos reclamation, occupational safety and environmental pollution. Apply a coat of BOND PLUS for the impregnation of the substrate and the incorporation of asbestos fibres, preventing any dispersions in the environment. The use of primer also favours the adhesion of the encapsulating coating, to be applied after the primer has dried (about 30–40 minutes depending on the temperature). BOND PLUS can be applied by spray (airless) with a consumption of about 100-300 grams/m2, depending on the degree of absorption of the substrate.

Mënyra e përdorimit

Spray ELASTOCAP-ABC onto clean and dry surfaces (at a pressure of 200–210 bar) once the BOND PLUS is completely dry. The product can be diluted with 15% water to facilitate application.
For TYPE A and B ENCAPSULATION COATINGS, application requires a minimum of two coats in different contrasting colours, waiting approximately 12–24 hours before the application of the next layer, in accordance with environmental conditions.
A single coat of ELASTOCAP-ABC is sufficient for NON-VISIBLE TYPE C COATINGS. The average and total minimum thicknesses required by current standards vary depending on the type of coating (see the table). The appearance of the underlying layer of cladding caused by environmental conditions and wear indicates a need to work on the surface once more to restore the encapsulant coating.

Mënyrat e përdorimit

- Spruco

Mjetet e pastrimit

- Ujë

Shtresat e lejuara

- Fibroçimento

Na kontaktoni

Vuoi saperne di più sui nostri prodotti?

Kujdes, plotëso saktë këtë fushë.
Kujdes, fut një adresë email-i të vlefshëm.
Kujdes, plotëso saktë këtë fushë.

Duke paraqitur pranoj politikat e privatësisë

Kujdes, plotëso saktë këtë fushë.

Përfundimi regjistrim në Newletter

Ndaj

Produkte në vitrinë

  • Readymesh
  • Concrete Repar
  • Sanawarme