EG 91

Epoxy-polyurethane two-component, thixotropic, elastomeric sealant

Kodi: PRS.0034

Përbërësit: 2

Pamja: I lëngshëm

Two-component, thixotropic elastoplastic sealant, for joints subject to traffic: shore hardness >90; elastic deformation >70 %; to be levelled out or extruded in the suitably taped joint sections (to protect the adjacent surfaces). Resistant to contact with hydrocarbons (gasoline and diesel fuel).

Linee di appartenenza

Vetitë themelore

jetëgjatësia

Jetëgjatësia: 12 muaj

temperatura-e-aplikimit

Temperatura e aplikimit: +5 / +35 °C

pesha-specifike

Pesha specifike: 1.25 kg/dm³

raporti-i-përzierjes

Raporti i përzierjes: 4:1 _

pot-life

Pot life: 20 min

material-i-ndezshëm

Material i ndezshëm

puthitja-me-mbështetësin

Puthitja me mbështetësin: 2.5 N/mm²

produkt-me-bazë-tretës

Produkt me bazë tretës

Veçoritë teknike

Ngurtësimi

14 _

Tërheqja deri në këputje

300 %

Viskoziteti

1750000 ±5% mPas

Ngurtësimi i plotë

7 ditë

Rezistenca në tërheqje

2.6 N/mm²

Raporti i katalizatorit

4:1 _

Ngurtësim në prekje

8 h

Resistance to abrasion

120 mg

Ngurtësim me prekje

30 ±3.5% min

Mbetje e thatë

98 ±1 %

Ngjyrat në dispozicion

- Gri

Amballazhime dhe përmasa

- Kanoçe 4 kg [A]

- Kanoçe 1 kg [B]

- Kit: 1 Kanoçe 4 kg [A] + 1 Kanoçe 1 kg [B]

Konsumi

Approximately 1.25 kg of EG 91 per cubic decimetre of joint volume to be sealed (1250 kg per cubic metre).

Fushat e përdorimit

Horizontal sealing of joints in industrial flooring, even in the presence of chemical attacks and stresses from average-heavy traffic. Vertical sealing of joints in concrete works and products.

Përgatitja e shtresave

The application and containment surfaces (joint walls) should be clean, dry, conveniently prepared and adequately resistant: free from dust, grease, soiling, crumbling and/or non-adhering parts and dry. The application surfaces must also be preliminarily treated with PROTECH FLEX PRIMER.

Mënyra e përdorimit

Add component B to component A taking care to pick up all the material contained in the packs, mix thoroughly with a mixer at a low number of revolutions, until a perfectly homogeneous mix is obtained; add the required load amount (component C) continue to mix until a perfectly homogeneous mixture is obtained, indicated by the uniform colour of the mixture. Apply the product mixed by trowelling or with extrusion guns.
Do not apply with temperatures below + 5°C or higher than + 35°C and in the presence of surface stagnant water.

Mënyrat e përdorimit

- Shpatull

- Pistoletë me dozë të përcaktuar

Mjetet e pastrimit

- UNI solvent

Shtresat e lejuara

- Beton

- Parafabrikuara

- Sipërfaqet metalike

Ndaj

Produkte në vitrinë

  • Syntech Poliurea
  • Floortech Prerit
  • Readymesh