Corrosion inhibitor by impregnation for concrete structures

Kodi: CSX.0247

Përbërësit: 1

Pamja: I lëngshëm

CONSILEX NO-RUST is a powerful non-toxic corrosion inhibitor, to be applied to the surfaces of concrete structures and which, thanks to its particular chemical nature, migrates within the conglomerate and deposits on its particular internal reinforcement substances that preserve their integrity over time, by inhibiting oxidation phenomena.

Linee di appartenenza

Vetitë themelore


Pesha specifike: 1.03 kg/dm³


Temperatura e aplikimit: >0 °C


Jetëgjatësia: 24 muaj


Të përdoret me doreza mbrojtëse


Pa tretës

Veçoritë teknike


9.0-9.5 _

Produkt jo filmik

Ngjyrat në dispozicion

- Qelibar

Amballazhime dhe përmasa

- Bidon 10 kg

- Bidon 25 kg

- Bidon 5 kg


CONSILEX NO-RUST performs its function effectively based on the migration phenomenon, which allows it to deposit on the reinforcement of the treated structure of particular corrosion inhibiting agents, even applied to the outer surface of the structure itself!

The particular formulation of CONSILEX NO-RUST allows its effectiveness not to be compromised by the presence of high levels of chlorides in the conglomerate. Alternative nitrite-based products, indeed, in the presence of chlorides, they may even have a negative effect on the corrosion of the reinforcing rods. CONSILEX NO-RUST, on the other hand, can be used effectively on concretes whose irons have already started to suffer corrosive effects and partial oxidation, also due to chlorides.


Apply from 0.15 to 0.35 kg of CONSILEX NO-RUST per square metre of surface to be treated.

Fushat e përdorimit

Preventive protection of existing concrete structures, such as public works, road works, buildings, hydraulic works, etc.

Përgatitja e shtresave

Thoroughly clean the support before applying the product, removing traces of fats, oils, dirt, incrustations, fouling, etc. Remove any paints, coatings, films or membranes that may be present on the surface: the product works by penetration, so it must come into direct contact with the surface of the concrete.

Mënyra e përdorimit

Spray-apply on the surfaces to be treated. In the case of structures for which there is a risk that corrosion phenomena are already in progress, apply two coats. Allow the surface to dry for a few minutes after application.
If you squirt the product accidentally on the glasses, paints, frames, etc., simply wash with abundant water.

In case the treated surface should then be treated or coated with paint or other coatings, please note that a thin layer of inhibitor may be deposited on the surface. In this case, wash with plenty of water and carry out preliminary adhesion tests on the coating that you intend to use. In case the tests fail, proceed with hydrocleaning or slightly sanding to remove any residue. Carry out preliminary tests in this case as well.

Mënyrat e përdorimit

- Ngopje

- Spërkatje pa ajrim me presion të ulët.

- Spruco

Mjetet e pastrimit

- Ujë

Shtresat e lejuara

- Beton

- Llaçe çimentoje, gëlqereje e të përziera

- Parafabrikuara

Na kontaktoni

Vuoi saperne di più sui nostri prodotti?

Kujdes, plotëso saktë këtë fushë.
Kujdes, fut një adresë email-i të vlefshëm.
Kujdes, plotëso saktë këtë fushë.

Duke paraqitur pranoj politikat e privatësisë

Kujdes, plotëso saktë këtë fushë.

Përfundimi regjistrim në Newletter


Produkte në vitrinë

  • Opus Dry
  • Osmocem
  • Pro Seal